How to make a box kite

 OK, I want to bring out the kid in you this week.  We are going to make a box kite using our Proxxon tools and hopefully it will fly and so will your spirits.  Trust me!

Supplies and equipment:

6    1/4" x 36" dowel rods

4   Walmart bags

2-3 drinking straws

kite string or suitable substitute

scissors

gorilla glue

contact cement 

plastic tape

measuring tool  yardstick or tape measure

speed square if you got one. 

Proxxon scroll saw

Proxxon profession rotary tool

Patience  ha ha

Here's our plan

Let's get started.   The first thing to do is to  cut (4) 14" pieces of dowel   These will be our cross pieces.  I used the Proxxon Scroll saw to do my cutting.  But I could have used my Proxxon mini bandsaw just as well.  You choose,

I made some indents using the Proxxon professional rotary tool.  This will help keep the parts from slipping while I lash them together.  

I lash them together in the middle with string, wrapping it around every which way until it kind of holds it together as an X.  Then I applied a drop or 2 of gorilla glue to strengthen it.   Gorilla glue is very strong but also very light.

Meanwhile I cut my straws into 2-3" lengths.  I need 8 of these.  I cut them about half way through at their halfway point.   These are really going to help keep things together.  I don't know if you noticed how hard it is to stabilize two round things together...😆
I slipped those over the 4 outside 36" dowels at the 6 " mark.  Note the picture below as how to use the straws.  

I put a drop of glue into 2 adjacent dowel sticks straw holes in each of the 4 36" dowels  then put two pieces of each cross members into the straws then propped them up to dry.  Try to keep them at pretty much 90 degrees to each other.

When it is good and dry turn it over and do the other sides just the same.   Now we have a skeleton.

Part 2, making the skin.

  Take 3 Walmart or similar bags and lay then out straight as you can.  Measure 12 inches out of the middle so that when cut it turns into a big loop.  Cut it down the side so you now have a sheet of plastic 12" wide.  Starting at one corner secure the plastic to the side using contact cement.  Then wrap the plastic around the frame as far as you can get.  I got around 3/4 of the way so I needed to add another length of plastic bag.  I attached the second plastic  to the first with a line of contact cement and finished the journey around the frame.  I cut off the excess and secured the end to the first piece at the first corner.  To add strength and durability to the wispy plastic I took clear packing tape around all the edges of the plastic.    

Part 3  Kite string

First let me say.  "goooood luck"   I went to Walmart, dollar tree, dollar general, etc etc.  I believe they have done away with it.  I did find a kite at dollar tree with a miniscule amount of string.  So use what you can.  Light but strong.  I finally chose yarn.  

Cut a piece 36 inches long and secure it to the top of the kite and the top of the bottom section of the kite.  (12" up from the bottom).  About 12- 14" down from the top, tie a small loop.  Attach your "string to' this loop.

Hey,,, guess what.  If there is some wind outside we are ready to fly.    I had to wait 3 days to get enough wind for take off.   But it was worth it.!  You are never too old to fly a kite!  Try it.  

                                                                                                                                                                                                   ↖Me, having a great day.    

Thank you all for visiting.  I do hope you give it a try.  Invite the kids or grands so you have an excuse.to play.    I had soooo much fun.

Thank you Proxxon for your fine tools that make making stuff so easy.  

Till next time.   Carol