How to make a Candleholder by using Proxxon Tools

Materials Needed For This Project:

Proxxon Band Saw

Proxxon Delta Sander

Proxxon Rotary Tool w/ Drill bit

Kapro Measure Mate 313

Drill w/ hole saw blades

Screws

Plaid Coastal Texture Paint- Sand Dollar

Plaid Folk Art Glitterific- Clear Hologram

Paint Brushes

Scrap Wood

To begin with I used my Kapro Measure Mate 313 to measure the length of my scrap 2 x 4 to the length of 14 1/2" and my scrap 1 x 3 piece of wood to length of 13 1/2". 

I cut the scrap pieces of wood with my Proxxon Band Saw to the measurements of 14 1/2" and 

13 1/2". I took the piece of 2 x 4, marked it and centered the 1 x 3 on top of it. I measured the center of the 1 x 3 for placement of the holes that I cut for my tealights and then I just eyeballed the placement for the two tealights on either side of it. Once I had them marked I used a hole saw blade that was 1 1/2" across to cut the holes for the tealights which fit inside perfectly. 

I used my  Proxxon Rotary Tool w/ Drill Bit to drill countersink holes for the screws that I used to put my two pieces of wood together.

After my wood was screwed together I used my Proxxon Delta Sander to smooth out the whole piece.

Here's what my wood looked like prior to using the Plaid Coastal Texture Paint (Sand Dollar)

Doesn't that paint look awesome? I only had to use one coat too! I was going to use the Plaid Glitterific-Red to begin with and then changed my mind and decided to use the Plaid Glitterific Paint-Clear Hologram which really does pick up or reflect on the color around it.

I loved the way this tealight holder turned out and it would look great as a decor piece for all the time. I'm going to be using it in another project with another product so stay tuned to see where it turns up next!

Proxxon Tools are really the bomb ya'll! You really need to check out their tools. While you're at it check out the Plaid website and see their products too. 

Please leave a comment as I read everyone.

Barbara

A Review of the Hot Wire Cutter

Hi everyone, Steph Ackerman here with another Proxxon review.  Today, I will share with you one of my favorite go to tools - the Hot Wire Cutter.  It was also one of the very first tools I got from Proxxon. 

The Hot Wire Cutter is a bench top unit approximately 15 1/2" x 11", allowing ample room to cut foam of any size.  The grid printed on the unit allows for even cutting.  The arm, extending approximately 5" over the unit, holds the wire and it is easily repositionable to cut a variety of angles.  The wire heats in less than one second so you can cut foam immediately.  The LED light reminds you not to ouch the wire.  The unit comes with approximately 90' of wire so it will last a very long time.

The Hot Wire Cutter is easy to assemble.  Removing it from it's packaging you simply adhere the arm and wire so set up is quick and easy.  It is literally a plug and go tool. 

Foam cuts like butter and you can even cut ribbon so it doesn't fray.

Here are some of the projects which I've created using the Hot Wire Cutter.  Click on the links for the complete project details.

Valentine's Day Heart

Fall Sign

Mini Packages

Tombstone

I hope you give the Hot Wire Cutter a try.  I know you will love it!

Thanks for stopping by.

How to Make an Adirondack-style Lounge Chair for an 18" Doll

Any little girl will be thrilled to be the recipient of this doll-sized Adirondack-style lounge chair. Their dolls will enjoy hours of relaxation as they lounge on the chair.

Supplies and Equipment to Make the Doll-sized Adirondack-style Lounge Chair

• 1" x 2" length of lumber cut as follows"
• Two 7" lengths
• Two 9¾" lengths
• Four 1" lengths
• 11 paint stir sticks cut in 6" lengths
• FolkArt Outdoor acrylic paint (I used Luau.)
• Strong liquid adhesive
• Proxxon Table Saw FET or Proxxon Chop and Miter Saw KGS 80
• Proxxon Bandsaw MBS/E
• Proxxon Delta Sander OZI/E

Instructions for Making the Doll-sized Adirondack-style Lounge Chair

1. All of the 1" x 2" pieces are cut at a 35° angle on each end. The angles are parallel with one another. If using the table saw, adjust the angle stop to 35° and set blade height. 
   
2. If using the chop and miter saw, release the table and move to 35°.
   
3. These are the pieces from the 1" x 2" length of lumber.
   
4. Sand the lettering off the paint stir stick with the Delta sander. You will only need 6", so there's no need to sand the entire length of the stir.
   
5. Cut the stirs into 6" lengths using the bandsaw.
6. Use the Delta sander to sand any rough edges on the 1" x 2" pieces
7. Assemble the chairs, keeping the slope of the 35° angle. Glue the 1" legs onto the bottoms of the 9¾" seat supports. Let the glue set.

   

   Legs glued to seat supports

8. Glue the 7" back support to the top of the 9¾" seat supports.
   
    
9. Glue the 6" stirs in place. A.) Begin at the back of the seat, then position the front seat slat followed by the center seat slat. Glue the last two seat slats in place. B.) Turn the chair so it rests on the back. Begin where the back meets the seat, then position the top slat followed by the center back slat. Glue this in two stages, letting the glue set after the seat slats are positioned.
10. Glue the last stir to the front of the chair.
11. Paint the lounge chair.
    
12. Plan a picnic or a pool party!!
    

Note: I found the pattern for this doll furniture at 100 Things 2 Do.

Carole

How to make a cowboy nightlight

Today I am going to show you a couple of neat little tricks you can do using proxxon tools and a few household items.   The plan is to make a little accent piece that you could also use as a nightlight.  I am going to show you how you can bend some wood using the proxxon table saw and water.

Equipment and Supplies:

1/4" thick plywood piece large enough to fit your silhouette picture

little branch pieces  (from the yard)

small artificial tea light  (dollar  tree)

 Plaid apple barrel paint- black 20504E)

paintbrush

adhesive spray (optional)

glue or glue gun.

Proxxon mini table saw.

Proxxon scroll saw

Drill and drill bit.

around the house stuff:

pan to hold water. 

 Weight to hold the piece down (I used a can of soup)

roll of paper towel or other round object

length of cord, rope, or shoestring

The first thing I did was to choose a silhouette picture I thought would look good as a nightlight.  I chose this picture because I was thinking the light would look good as a campfire.  I cut it straight where the fire was on the picture.  We will provide our own "fire"

I used the adhesive spray to temporarily affix it to the wood.  The next step is to cut it out.  I used the proxxon scroll saw for this.  For the inside cuts I first drilled a small hole and threaded my blade through the hole.

After removing the paper from my wood, I sanded it all smooth using the Proxxon OZI/E delta sander.↗

Next, we are going to use the Proxxon mini table saw.  First I removed the splitter and blade guard and lowered the blade to about 1/8" height.  Using the miter gauge I made lengthwise parallel cuts approximately 1/2" apart.  Notice I used the flat side of the piece against the guide to keep the piece square. 

this is the backside after it was cut. 

 Notice the cuts are approximately halfway through the thickness

Next, I put my cowboy in a pan and covered him with water.  Since wood floats, I placed a weight on it to keep it submerged.  I left it there for a few hours.   This softened the wood up a little bit.  Now I could bend it around the paper towel roll.  Any round object that is big enough will do.   I secured it with a strap and left it to dry.

Now it has a nice curve

Using Plaid apple barrel paint. I painted the whole thing black.  I also painted my little artificial tea light black, and added black smudges to my little branch pieces. These I glued onto the light to look like a campfire.

When everything is dry, it's done!   Place the little light behind the cookpot.   It really looks like a campfire!   And it is going to look great in the dark!

I had fun making this.    I ALWAYS have fun making stuff with my proxxon tools.  Thank you Proxxon.  They are the perfect tools for crafters and hobbyists.!  I know I only used black paint in this project, BUT, Plaid makes so many products.     Check em out at plaidonline.com    Guaranteed you will get inspired.    Thank you Plaid.

Thank you SO much for visiting. 👍  Till next time, play safe.🔨   Carol

Proxxon Tools help make the best Valentine Decorations!

Well it occurred to me the other day that it's really not that far until Valentine's Day. I thought I would just put something together for the occasion. 

Supplies Needed for this Project:

Plaid Paints : Folk Art Home Decor Chalk Paint, White Adirondack

Plaid Paint : Folk Art Home Decor Chalk Paint, Imperial

Proxxon Delta Sander

Proxxon Table Saw

Sandpaper

Paint brushes

Birch Plywood

Red Twine

Black Brush Tip Marker

Vinyl 

Cardstock

Pencil

To begin with you need to cut your wood down to size. I used my Proxxon Table Saw to accomplish the task. Just like cutting butter! This wood was a piece that I had left over from doing the chalkboard on the last post. The piece was 12 3/4" H x 13 1/2" W and I cut it down to 12" H x 10" W.

The Proxxon Delta Sander has got to be the handiest sander that I have.

I used it to sand all of the edges of the board that I was using. It made all of the edges very smooth and I also used it to take off any marks that were on the wood, such as pencil marks, and scuff marks. Once that was completed I took the time to draw three hearts onto the cardstock and cut them out. I used them for patterns and traced them onto some vinyl that I had and then cut them out of the vinyl. Next step was to paint the board both front and back with the Folk Art Home Decor Chalk Paint - White Adirondack next was to take the backing off of the vinyl hearts and eyeball where you want to place them on the board. After that was finished you need to paint the board with the Folk Art Home Decor Chalk Paint - Imperial. I used a piece of sandpaper and distressed the board by hand and then pulled off the vinyl hearts, which left white hearts showing through the red. Take your twine and wrap it around the board a few times and then tie a bow in the ends. Use your brush tip marker to write the word Love very small in the bottom heart. 

There you have it! A very shabby chic piece of Valentine's Day decor. Now I placed mine in this holder but you could easily put a hanger on the back and hang it on the wall. This piece was fairly easy to make and I would recommend anyone with the proper Proxxon Tools!

If you got any money for Christmas you might want to invest in some Proxxon Tools!

Barbara

How to Make a Rustic Snowman Decoration

The holidays may be over, but for us, it's still winter. And for me that means winter-themed decorations. Here's a sweet rustic snowman decoration that is sure to melt your heart. This is the perfect beginner project for getting to know to know your Proxxon tools.

Supplies and Equipment for Making the Rustic Snowman

• Scrap wood or MDF
• 1/8" dowel
• Buttons
• Ribbon
• Strong liquid adhesive
• Grey and white acrylic paints
• Artist's cement (optional)
• Proxxon Bandsaw MBS/E
• Proxxon Disc Sander TSG 250
• Proxxon Drill Press TBM 115
• Proxxon Delta Sander OZI/E

Instructions for Making the Rustic Snowman

1. Dimensions for this snowman can vary, depending on what scraps you have available. You're only limited by the working tolerances of your machines. My snowman's overall measurements are 4¼" tall x 1" wide x ¾" deep, made with three smaller blocks.
2. Begin by marking your cutting lines on the scrap lumber.
   
    
3. Cut pieces for head, middle body, and bottom body on the bandsaw. Don't be worried about exactness; a few wonky cuts adds character to the finished piece. In fact, you can plan wonky cuts :) The goal is to get comfortable using your tools.
   
4. Sand the pieces on the disc sander.
   
5. Drill holes on the bottom of the head piece, top and bottom of the middle body piece, and top of the bottom body pieces to accommodate the dowels. These holes don't need to be exactly positioned, but should come close to the center of the piece.
   
6. Paint the pieces with a coat of gray acrylic paints, and let dry thoroughly. Next, paint one of two coats of white acrylic, depending on the coverage you get and the look you want. Some of the grey paint shadowing through the white give an even more rustic look. Let paint dry.
   
7. Option: Coat the pieces with artists' cement to create texture. Let the cement cry thoroughly.
   
8. Sand each piece using the Delta sander. How much you sand and expose the grey paint and the base substrate will determine how rustic your snowman will be. Remember: you can also sand more.
   
9. Use a strong liquid adhesive to secure the dowels in place. The dowels give added support to keep the pieces together.
   
10. Decorate your snowman with a ribbon scarf and buttons. If desired, add facial features with a Sharpie or paint.